MWD which in full is Measurement While Drilling is measurement taken when drilling on an angle of inclination to the vertical line. These measurements are taken by the MWD Drilling Software. This data is used to produce a 3-D plot of the path of the oil well. This software will transmit crucial information to the operator during operations.
There are different types of information transmitted by the software one being the direction of the well. Real time directional surveys and its transmission are very possible. Measurement of the azimuth and the inclination of the hole at that location are done by the magnetometers and accelerometers. There is therefore real time transmission from the site to the surface.
The data transmitted at intervals of 10m to 500m is then analyzed on the surface to calculate the location of the wellbore. It is necessary information for the company since it acts as a proof that it is not operating outside the block it is licensed to prospect. When operating vertically or near vertical direction this technology is not used due to its high cost.
The surveys is mainly used in directional-drilling. Directional-drilling forms the main or core part of any survey. Finding and moving towards the target zone of the well will be made easier by this information. Directional-drilling is aided by MWD by the provision of tool face measurements which uses downhole mud motors with bent housing or bent.
The software sends information about the mechanics of the drill bit. This kind of information include the downhole temperature, mud flow volume, smoothness of rotation, the drillstring speed of rotation, the weight as well as torque on the dril bit. This info will lead to more efficient operations. It also ensures that the tools used won't fail when drilling because they can be operated within their technical specifications. Geologists use this information to understand the formation of the zone being drilled.
MWD tools are able to measure the properties of the formation and send the information to drillers when process is ongoing. The measure of the formation properties can be done by the MWD then sent to the drillers while operation is in progress. This information is basically used in geosteering to the targeted zone. The data obtained varies It is from variants such as porosity, acoustic-caliper, density, inclination at the drill bit and resistivity that this information oscillates.
There is also the measurement of natural gamma rays measurements at the well using internal gamma ray sensor installed in MWD tools. The sensors cost a lot, are compact and able to take measurements when drilling unmodified drill collars. Compacts and cheap sensors will do unmodified drill collars during operations. MWD software cuts the various process costs and increases the lifespan of the drill bits.
The data they get during the operations is either transmitted by the mud-pulse telemetry method and electromagnetic telemetry. In the mud-pulse telemetry method the mud valve downhole which restricts the flow of slurry creates pressure differences which are send to the surface as for analysis. It can either be positive, negative pulse/continuous wave.
Electromagnetic telemetry method of data transmission by the MWD software involves generation of altered voltage different in the upper part and the lower portion of the electrical insulator used in the drillstring. A wire attached to the wellhead on the surface and another wire attached to the rod form the electrodes of a dipole antenna. From these electrodes the voltage signals are obtained and analyzed to give information.
There are different types of information transmitted by the software one being the direction of the well. Real time directional surveys and its transmission are very possible. Measurement of the azimuth and the inclination of the hole at that location are done by the magnetometers and accelerometers. There is therefore real time transmission from the site to the surface.
The data transmitted at intervals of 10m to 500m is then analyzed on the surface to calculate the location of the wellbore. It is necessary information for the company since it acts as a proof that it is not operating outside the block it is licensed to prospect. When operating vertically or near vertical direction this technology is not used due to its high cost.
The surveys is mainly used in directional-drilling. Directional-drilling forms the main or core part of any survey. Finding and moving towards the target zone of the well will be made easier by this information. Directional-drilling is aided by MWD by the provision of tool face measurements which uses downhole mud motors with bent housing or bent.
The software sends information about the mechanics of the drill bit. This kind of information include the downhole temperature, mud flow volume, smoothness of rotation, the drillstring speed of rotation, the weight as well as torque on the dril bit. This info will lead to more efficient operations. It also ensures that the tools used won't fail when drilling because they can be operated within their technical specifications. Geologists use this information to understand the formation of the zone being drilled.
MWD tools are able to measure the properties of the formation and send the information to drillers when process is ongoing. The measure of the formation properties can be done by the MWD then sent to the drillers while operation is in progress. This information is basically used in geosteering to the targeted zone. The data obtained varies It is from variants such as porosity, acoustic-caliper, density, inclination at the drill bit and resistivity that this information oscillates.
There is also the measurement of natural gamma rays measurements at the well using internal gamma ray sensor installed in MWD tools. The sensors cost a lot, are compact and able to take measurements when drilling unmodified drill collars. Compacts and cheap sensors will do unmodified drill collars during operations. MWD software cuts the various process costs and increases the lifespan of the drill bits.
The data they get during the operations is either transmitted by the mud-pulse telemetry method and electromagnetic telemetry. In the mud-pulse telemetry method the mud valve downhole which restricts the flow of slurry creates pressure differences which are send to the surface as for analysis. It can either be positive, negative pulse/continuous wave.
Electromagnetic telemetry method of data transmission by the MWD software involves generation of altered voltage different in the upper part and the lower portion of the electrical insulator used in the drillstring. A wire attached to the wellhead on the surface and another wire attached to the rod form the electrodes of a dipole antenna. From these electrodes the voltage signals are obtained and analyzed to give information.
ليست هناك تعليقات:
إرسال تعليق